Connected Vehicle Roadside Equipment --> Vehicle:
intersection status

Definitions

intersection status (Information Flow): Current signal phase and timing information for all lanes at a signalized intersection. This flow identifies active lanes and lanes that are being stopped and specifies the length of time that the current state will persist for each lane. It also identifies signal priority and preemption status and pedestrian crossing status information where applicable.

Connected Vehicle Roadside Equipment (Source Physical Object): 'Connected Vehicle Roadside Equipment' (CV RSE) represents the Connected Vehicle roadside devices (i.e., Roadside Units (RSUs)) equipped with short range wireless (SRW) communications technology, as well as any other supporting equipment that leverage the RSU and are not described by other objects (e.g., a local roadside processor). CVRSE are used to send messages to, and receive messages from, nearby vehicles and personal devices equipped with compatible communications technology. Communications with adjacent field equipment and back office centers that monitor and control the RSE are also supported. This device operates from a fixed position and may be permanently deployed or a portable device that is located temporarily in the vicinity of a traffic incident, road construction, or a special event. It includes a processor, data storage, and communications capabilities that support secure communications with passing vehicles, other field equipment, and centers.

Vehicle (Destination Physical Object): This 'Vehicle' physical object is used to model core capabilities that are common to more than one type of Vehicle. It provides the vehicle-based general sensory, processing, storage, and communications functions that support efficient, safe, and convenient travel. Many of these capabilities (e.g., see the Vehicle Safety service packages) apply to all vehicle types including personal vehicles, commercial vehicles, emergency vehicles, transit vehicles, and maintenance vehicles. From this perspective, the Vehicle includes the common interfaces and functions that apply to all motorized vehicles. The radio(s) supporting V2V and V2I communications are a key component of the Vehicle. Both one-way and two-way communications options support a spectrum of information services from basic broadcast to advanced personalized information services. Advanced sensors, processors, enhanced driver interfaces, and actuators complement the driver information services so that, in addition to making informed mode and route selections, the driver travels these routes in a safer and more consistent manner. This physical object supports all six levels of driving automation as defined in SAE J3016. Initial collision avoidance functions provide 'vigilant co-pilot' driver warning capabilities. More advanced functions assume limited control of the vehicle to maintain lane position and safe headways. In the most advanced implementations, this Physical Object supports full automation of all aspects of the driving task, aided by communications with other vehicles in the vicinity and in coordination with supporting infrastructure subsystems.

Included In

This Triple is in the following Service Packages:

• ST08: Eco-Approach and Departure at Signalized Intersections
• TM04: Connected Vehicle Traffic Signal System
• VS12: Vulnerable Road User Safety
• VS13: Intersection Safety Warning and Collision Avoidance
• VS15: Infrastructure Enhanced Cooperative Adaptive Cruise Control

This triple is associated with the following Functional Objects:

• RSE Intersection Management
• RSE Intersection Safety
• Vehicle Eco-Driving Assist
• Vehicle Intersection Warning

This Triple is described by the following Functional View Data Flows:

• intersection_collision_avoidance_data
• intersection_status_data_for_vehicle
• signal_phase_indication_to_vehicle
• signal_phase_response_state_to_vehicle
• signal_phase_timing_to_vehicle
• vehicle_signage_intersection_message

This Triple has the following triple relationships:

Communication Solutions

• EU: Signal Control Messages - BTP/GeoNetworking/G5 (20)
• US: SAE Signal Control Messages - LTE-V2X WSMP (23)
• US: SAE Signal Control Messages - WAVE WSMP (36)

Selected Solution

US: SAE Signal Control Messages - LTE-V2X WSMP

Solution Description

ITS Application Entity SAE J2735 ISO 19091 SAE J2945/B CTI 4501			Click gap icons for more info.
Mgmt SAE J3161 3GPP 24.301 3GPP 36.331	Facilities SAE J2735 SAE J2945	Security Bundle: IEEE 1609.2
	TransNet IEEE 1609.3
	Access Bundle: 3GPP LTE-V2X

Note that some layers might have alternatives, in which case all of the gap icons associated with every alternative may be shown on the diagram, but the solution severity calculations (and resulting ordering of solutions) includes only the issues associated with the default (i.e., best, least severe) alternative.

Characteristics

Security